Friday DIY: SolarFast Statement Earrings by Mad Mim

mad-mim_solar-fast-earrings_18

Today Miriam from the blog Mad Mim has this super creative and unusual earring tutorial for us. Read on to discover how to make your very own statement earrings using photo negatives!

For this project you’ll need some:

  • SolarFast Dye
  • SolarFast film and inkjet printer (there are other options if you only have a laser printer I’ll talk about it later)
  • SolarFast wash
  • Some white cotton fabric (only a bit!)
  • bright coloured embroidery floss
  • bright coloured beads
  • earring findings: hooks, jump rings and eye pins
  • pliers

 

How to:

Okay, let’s talk about the printing process. To begin you’ll need to choose and image and create a negative. *In photoshop or other photo editing software, you’ll need to first make it black and white, and then invert it (both options in the adjustment panel). Images with really high contrast do best (you want the darks black and lights white). If you need to, knock up your contrast just a tad and bring down your brightness levels a bit until you’re happy. Important!  **Once you print (print on the matte side of the film!) you want the dark parts of the image to be completely opaque–meaning if you hold it up to the light you can’t see any light shining through those parts; conversely the white areas will be completely transparent and then a variation of opacity for all the shades in between. You can adjust your printer to let out a heavy layer of ink, or you can double up your transparency which is what really worked for me (one layer was not opaque enough and I was getting just solid coloured squares).

*If you have no photo editing software, you can make these adjustments in your printer settings as well, mine said something like print in black and white and make a negative to invert. Also, if you take your image to a print shop they can easily make these adjustments as well.

**You must use an inkjet printer with the Solar Fast film because a laser printer will melt it. I don’t have an inkjet so I went to a print shop and had them print on a transparency. Transparency will work but sometimes has problems with not being waterproof and the ink bleeding. It worked fine for me, but I was told that that can be an issue.

Once you get your negative, the process is simple. Working on a non-absorbent surface (a clip board with a bit of plastic or plastic wrap worked great), paint the dye over the area that will be printed with a foam brush or sponge. You can tape it off or just go for it, whatever. Once you have a fully saturated area (enough that there is no dry spots), take a paper towel and really blot the heck out of it. It will be damp still, but you don’t want it to be wet feeling–you want to remove the excess liquid, it will make a clearer print. Put your negative down (shiny side which is the waterproof side face down) and secure ( a sheet of plastic glass and clips or something similar can be really helpful, you just don’t want that negative shifting at all).

blog-earrings.jpg
blog-earrings.jpg

Take outside and expose. Noon is the best time, but if you’re a little late or early(between 10-3 is best) just prop up your print so that’s it’s angled towards the sun. Exposure time varies depending on the colour you use and the weather, but my orange dye took only about 5 minutes to expose. Exposure time is important, it was one of my first mistakes–my prints were almost solid colours and barely discernible and it was partly due to over exposure at 20-30 minutes. With my print I discovered that even 10 minutes was too long. If you’re doing a larger scale project, I suggest doing a small test print to figure out optimal exposure time.

blog-earrings.jpg

Troubleshooting: The top row here didn’t have an opaque enough transparency, and the bottom piece was just a bit overexposed.

blog-earrings.jpg

blog-earrings.jpg

Rinse it immediately after bringing it in so that you remove any non-exposed dye! Rinse it with running hot hot water and wash with the SolarFast wash. Machine washing is best, but because I was just doing such small pieces I hand washed vigorously.

To assemble the earrings I made two prints for each earring (front and back),cut into my desired shape and applied some iron on interfacing to the back. I then sandwhiched some thicker canvas fabric in between my printed fabrics and glued together with a glue stick.

blog-earrings.jpg

Blanket stitch with your embroidery floss around the edge (threading your tails to the inside)

blog-earrings.jpg

and then poke an eye pin through the top.

blog-earrings.jpg

Add a couple bright coloured beads, and then snip off excess wire and bend the top into a loop. Attach a small jump ring then attach that to an ear-wire.

blog-earrings.jp

Pretty cool stuff, right?

 

If you like this article, bookmark the page or share it with friends:

Post from Oliver

write at 23.05.2014 - 15:54.

About Oliver

Oliver works on acquistions, but you will also see his name pop up here and on Twitter. Originally from England, he enjoys travelling and really wants a pug. » more from Oliver

Comments